Manual casting air sandblasting booth/blast cleaning booth/sand blasting room main component:
Sand blasting assembly
Sand blasting circulation system (honeycomb floor, sand suction pipe, shot slag separator)
Dust removal system
Electrical control system and other parts.
Qingdao Xinsa Machinery Manufacturing Co., Ltd,independent R&D design this pitless pneumatic recycle sand blasting chamber.the only one that owns this technology of pitless sandblasting room all over the word.
Comparison of environmental protection pneumatic recovery sandblasting room's characteristics with mechanical recycling sandblasting room:
1.Low cost of integrated operation and energy saving.
Pneumatic recovery Sandblasting room mode with no transmission mechanism is adopted, and the failure rate is low and maintenance is free. Reduce the maintenance time of the shutdown, and reduce the loss caused by the shutdown and maintenance;
2.the honeycomb floor has a sand-back structure without digging pit, and the civil engineering cost and the construction period are greatly reduced;
3.The structure is simplified and the interlocking control can be used in each system control, which greatly improves the convenience of maintenance and repair.
4.The key wear parts are equipped with standard modules, which are easy to maintain and replace, thus avoiding heavy maintenance work.
5.The sandblasting chamber adopts the upper supplementary air, the lower part and the side part can carry on the dust suppression circulation mode. The dust always drains downward, the visibility in the room is high, the working environment is good, the quality and efficiency of sand blasting are guaranteed, and the physical and mental health of the workers is protected.
6.The whole sand absorbing floor can recover all the sand materials in an instant, and there is no residual sand material on the ground. The sand blasting room is clean and clean in the room, no manual cleaning is required, and the working time is saved. Pneumatic pipe back sand, abrasive recovery up to 99, easy to clean the abrasive. Traditional mechanical recovery (or scrape floor) sandblasting room is almost impossible to thoroughly clean and replace abrasives.
7.The body of sandblasting room is simple and beautiful, and the installation is convenient and flexible.
8.The whole technical performance of sandblasting room is advanced, dust emission meets and is lower than the national and local environmental protection requirements, and the environmental pollution is completely eliminated.
Abrasive blasting chamber equipment 's technical parameters:
Manual casting air sandblasting booth/blast cleaning booth/sand blasting room cleaning effect:
Before clean:
After clean:
Application case:
Clean freighter stringer
Clean car shelf :
Our company show:
According to your requirements, the most suitable machine will be designed for your workpieces, please indicate the following details.
1. What kind of workpiece you clean?
2. The workpiece size, length, width, height and weight of maximum workpiece.
3. What's your production capacity per day (8 hours)?
4. It's my pleasure if you can provide details workpiece photos to us.
Based on these details information, the detailed technical proposals will be sent to you for reference.
FAQ:
After-sale service:
1. Installation and commissioning issue: We will send one technicians to assist with machine installation and commissioning, customer pays for return tickets, hotel and diet. Customer need arrange skilled worker and prepare various installation machinery and tools.
2. Warranty time:12 months from date of commissioning completion, but no more than 18 months from date of delivery.
3. Supply full english documents: including general installation drawings, pit design drawings, manual book, electric wiring diagram, electric manual book and maintenance book, etc.
4. Exported experience : Many countries, such as The USA, Russia, UK, Ukraine, Australia, Malaysia, UAE, Egypt, Mexico, Brasil, etc.
5. Our shot blasting spare parts are high quality with Cr20S High Chrome, ZGMn13, Mn65, etc.
Trade Information:
MOQ: 1set.
Settlement Currency: USD, RMB, EUR.
Trade mode: FOB (FCA), CIP, CFR, CIF, DDU, DDP, Turnkey.
Payment term: 30% deposit by T/T, the balance paid before delivery or L/C at sight.
Delivery time: Within 20-60 days according to different type equipment.
Any question pls kindly contact with us and welcome to visit our factory!
We also can design and manufacture all kind of non-standard sand blasting chamber according to customer's different workpiece detail requirement,weight and productivity.
Sand blasting assembly
Sand blasting circulation system (honeycomb floor, sand suction pipe, shot slag separator)
Dust removal system
Electrical control system and other parts.
Qingdao Xinsa Machinery Manufacturing Co., Ltd,independent R&D design this pitless pneumatic recycle sand blasting chamber.the only one that owns this technology of pitless sandblasting room all over the word.
Comparison of environmental protection pneumatic recovery sandblasting room's characteristics with mechanical recycling sandblasting room:
1.Low cost of integrated operation and energy saving.
Pneumatic recovery Sandblasting room mode with no transmission mechanism is adopted, and the failure rate is low and maintenance is free. Reduce the maintenance time of the shutdown, and reduce the loss caused by the shutdown and maintenance;
2.the honeycomb floor has a sand-back structure without digging pit, and the civil engineering cost and the construction period are greatly reduced;
3.The structure is simplified and the interlocking control can be used in each system control, which greatly improves the convenience of maintenance and repair.
4.The key wear parts are equipped with standard modules, which are easy to maintain and replace, thus avoiding heavy maintenance work.
5.The sandblasting chamber adopts the upper supplementary air, the lower part and the side part can carry on the dust suppression circulation mode. The dust always drains downward, the visibility in the room is high, the working environment is good, the quality and efficiency of sand blasting are guaranteed, and the physical and mental health of the workers is protected.
6.The whole sand absorbing floor can recover all the sand materials in an instant, and there is no residual sand material on the ground. The sand blasting room is clean and clean in the room, no manual cleaning is required, and the working time is saved. Pneumatic pipe back sand, abrasive recovery up to 99, easy to clean the abrasive. Traditional mechanical recovery (or scrape floor) sandblasting room is almost impossible to thoroughly clean and replace abrasives.
7.The body of sandblasting room is simple and beautiful, and the installation is convenient and flexible.
8.The whole technical performance of sandblasting room is advanced, dust emission meets and is lower than the national and local environmental protection requirements, and the environmental pollution is completely eliminated.
Abrasive blasting chamber equipment 's technical parameters:
| Item | Unit | Numerical value | ||||
| Inner measurement of sand blasting room | L×W×H | mm | 6000×4000×3600 | |||
| Sand blasting room's door dimensions | W×H | mm | 3000×3000 | |||
| Max cleaning workpiece weight | Ton | 5 | ||||
| Cleaning workpiece speed | Externa l surface of profiled structural parts | sq.m./h | 20-30(A-D grade according the different cleaning requirements of original Surface material and workpiece | |||
| Cleaning quality rank | Reach Sa2 .5 rank | |||||
| Processing material and strength range | Q235/Q345/65Mn/HT/ZG etc. | |||||
| Surface roughness | μ | 40~75 depend on the shot ball's size) | ||||
| Total power | kw | About 20.5(Including lighting) | ||||
| Compressed air consumption | m³/min | 6m³/min,each spraying gun need 5 m³/min,protecting air-condition and the back flush dust cleaning need 1 m³/min | ||||
| Compressed air pressure | MPa | 0.5-0.7 | ||||
| Facility adaptive temperature | Suitable for Australia four seasons normal temperature | |||||
| Control system | electrical appliance control system | Manual button control, Suitable for local industrial power supply | ||||
| Ground pit requirement | Without digging pit,waterproof | |||||
| Overall noise | dB | ≤95 | ||||
| Dust discharge concentration | mg/m³ | better than 80mg/m³ of the GB16297-1996emission standard of air pollutants | ||||
Manual casting air sandblasting booth/blast cleaning booth/sand blasting room cleaning effect:
Before clean:
After clean:
Application case:
Clean freighter stringer
Clean car shelf :
Our company show:
According to your requirements, the most suitable machine will be designed for your workpieces, please indicate the following details.
1. What kind of workpiece you clean?
2. The workpiece size, length, width, height and weight of maximum workpiece.
3. What's your production capacity per day (8 hours)?
4. It's my pleasure if you can provide details workpiece photos to us.
Based on these details information, the detailed technical proposals will be sent to you for reference.
FAQ:
After-sale service:
1. Installation and commissioning issue: We will send one technicians to assist with machine installation and commissioning, customer pays for return tickets, hotel and diet. Customer need arrange skilled worker and prepare various installation machinery and tools.
2. Warranty time:12 months from date of commissioning completion, but no more than 18 months from date of delivery.
3. Supply full english documents: including general installation drawings, pit design drawings, manual book, electric wiring diagram, electric manual book and maintenance book, etc.
4. Exported experience : Many countries, such as The USA, Russia, UK, Ukraine, Australia, Malaysia, UAE, Egypt, Mexico, Brasil, etc.
5. Our shot blasting spare parts are high quality with Cr20S High Chrome, ZGMn13, Mn65, etc.
Trade Information:
MOQ: 1set.
Settlement Currency: USD, RMB, EUR.
Trade mode: FOB (FCA), CIP, CFR, CIF, DDU, DDP, Turnkey.
Payment term: 30% deposit by T/T, the balance paid before delivery or L/C at sight.
Delivery time: Within 20-60 days according to different type equipment.
Any question pls kindly contact with us and welcome to visit our factory!
We also can design and manufacture all kind of non-standard sand blasting chamber according to customer's different workpiece detail requirement,weight and productivity.